BMX DICTIONARY FOR BEGINNERS A- Z

4130: 

Refers to 4130 Chromoly, a metal alloy used abundantly in the production of BMX bicycles and parts. 4130 refers to the American Iron and Steel Institute’s code defining the composition of the alloy, the 41 specifically denotes a low alloy steel including Chromium and Molybdenum, which is where the name Chromoly comes from

20’s:

Twenty-inch bicycle wheels, the most common size wheel for BMX bicycles.

Axle:  

The shaft on which the wheel revolves.

Bars: 

An abbreviation of handlebars.

Berm:  

A corner on a track built up on the outside of a turn to create a banked curve.

BMX:  

Abbreviation for bicycle motocross.

Bottom Bracket:  

The mechanism at the bottom of the bicycle frame, which holds the spindle and crank.

Brakes:  

Any bicycle braking system which works by opening and closing two brake shoes on the rim in a clamping motion, like jaws.

Brake Lever:  

A lever mounted on the handlebar used for activating the brake.

Cables:  

Steel wires braided into cables and sometimes covered with plastic coating.  Cables are used to connect the brake levers to the brakes.

Case: 

Coming up short on a jump & the back wheel of the bike hits the peak of the landing.

Chain Stay:  

The part of the bicycle frame that runs parallel to the chain.  It connects the bottom bracket to the rear dropouts.

Chain Wheel:  

A one-piece front gear.  The chain wheel is attached to the bottom bracket and crank.

Clipless Pedals:  

Hook or “clip” to your clip less shoes.  Some clipless pedals have a cage around the outside of the pedals.

Crank:  

The L-shaped metal arm to which the pedals are attached.

Chromo: 

Refer 4130. 

Chromoly: 

As above.

Down Tube:  

Part of the bicycle frame, which slants downward at an angle.  It runs from the head tube to the bottom bracket.

DNS:  

Designation on a moto sheet that a rider “Did Not Start” in any particular race.

Drivetrain: 

The assembly unit on a bicycle consisting of the chainwheel, chain, and freewheel.

Dropouts:  

Small, slotted openings, which hold the front and rear wheel axles.

Expert:  

Highest level of amateur competition.

Frame: 

The main part of a the bicycle, on which all the smaller parts are attached. Consists of a top tube, down tube, seat stays, chain stays, seat tube, and head tube.

Fork:  

The double-pronged section of the frame, which holds the front wheel in place.

Freewheel:  

A one-piece rear gear that allows the rider to back-pedal.  Bearings are built in.

Gear Ratio:  

A number, which indicates the relationship between the two gears and tells you how much work a particular combination of gears will do.

Grips:  

Rubber or Plastic cover who goes on the handle bars at the end to aid in grip.

Headset:  

Bearing set for which your front end rotates on and your fork/handle bars slide into.

Head Tube:  

A short vertical tube at the very front of the bike.  The front fork fits inside the head tube.

Hole Shot:  

Taking the lead position out of the starting gate and going into the first turn.

Hub:  

Cylinder, which holds the axle of each wheel.

Huck: 

To throw oneself haphazardly into a trick or manoeuvre

Lip: 

The very top of the transition on a ramp, jump or earth mound, just before the coping

Lane:  

Position 1 thru 8 on the starting gate.

Moto:  

a.) A single racing heat. b.) Any riders specific race.

Moto Board:  

An area where the moto sheets are posted before and during the race.

Moto Number:  

Number corresponding with any specific race (moto).

Moto Sheet:  

Paperwork displaying the races in moto number order.

Novice:  

New rider to the sport.

Number Plate:  

Displays riders earned or temporary number for identification purposes

Platform Pedals:  

Are the most commonly used pedals for trails, street, and ramps. They have a platform that your foot rests on with little pegs that stick to your shoe.

Rims:  

Round part of the wheel that the tires attach onto.

Registration:  

Where you go to sign up to compete in a race (moto)

Sandbagging: 

Intentionally allowing other rider(s) to pass during a main event or within any round of a total points race so as not to gain wins towards classification advancement.

Seat Stays: 

Section of the frame, which runs from the seat tube to the rear wheel dropouts.

Seatpost: 

The tube, which holds the seat and goes into the frame.

Staging Area:  

The area where the riders gather for loading into the gate.

Starting Gate:  

Flat formed area with a hinged portion. This is where each race commences.

Stem:  

The part connected to the forks that hold the handlebars.  Sometimes referred to as a gooseneck.

Sprocket:  

Same as a chain wheel or either the front or rear gear assembly.  Sprockets are strong. They are a combination of a chain ring and a spider together

Top Tube:  

The top horizontal tube on a bicycle frame, between your head tube and seat tube.

Track Director or T.D.:  

a person who runs and maintains all aspects of a BMX track. Does all this for no pay to help the kids and parents who love BMX. Thanks to all track operators in BMX!

Volunteer:  

A VERY special person who voluntarily undertakes or expresses a willingness to undertake help for the track and riders for no pay or free merchandise.